Shaft keyseat
- Width b
- 0.250"
- Depth t1
- 0.125"
- d − t1 (from the opposite side of the shaft)
- 1.125"
From the shaft diameter: the right key, the shaft and hub keyseat with tolerances, and how much torque it carries.
Shaft diameter and fit type. The key and keyseat come from the standard.
ANSI B17.1 · Ø7/8"–1 1/4"
Square key: half of the key sits in the shaft and half in the hub. Nominal sizes; ANSI B17.1 gives the tolerances.
Guide: steel hub, steady load ≈ 100 MPa; cast iron ≈ 50 MPa; with shock loads, use half.
Nominal sizes per ANSI B17.1. Check tolerances against the standard or a catalog before machining.
| Shaft Ø over – up to (in) | Square key W × W (in) | Keyseat depth, shaft and hub (in) |
|---|---|---|
| 5/16 – 7/16 | 3/32 × 3/32 | 0.047 |
| 7/16 – 9/16 | 1/8 × 1/8 | 0.063 |
| 9/16 – 7/8 | 3/16 × 3/16 | 0.094 |
| 7/8 – 1 1/4 | 1/4 × 1/4 | 0.125 |
| 1 1/4 – 1 3/8 | 5/16 × 5/16 | 0.156 |
| 1 3/8 – 1 3/4 | 3/8 × 3/8 | 0.188 |
| 1 3/4 – 2 1/4 | 1/2 × 1/2 | 0.250 |
| 2 1/4 – 2 3/4 | 5/8 × 5/8 | 0.313 |
| 2 3/4 – 3 1/4 | 3/4 × 3/4 | 0.375 |
| 3 1/4 – 3 3/4 | 7/8 × 7/8 | 0.438 |
| 3 3/4 – 4 1/2 | 1 × 1 | 0.500 |
| 4 1/2 – 5 1/2 | 1 1/4 × 1 1/4 | 0.625 |
| 5 1/2 – 6 1/2 | 1 1/2 × 1 1/2 | 0.750 |
Parallel keys, high form. t1 is the keyseat depth in the shaft and t2 in the hub; in the shop you check d − t1 on the shaft and d + t2 in the hub.
| Shaft Ø over – up to (mm) | Key b × h | Shaft depth t1 | Hub depth t2 |
|---|---|---|---|
| 6 – 8 | 2 × 2 | 1.2 | 1 |
| 8 – 10 | 3 × 3 | 1.8 | 1.4 |
| 10 – 12 | 4 × 4 | 2.5 | 1.8 |
| 12 – 17 | 5 × 5 | 3 | 2.3 |
| 17 – 22 | 6 × 6 | 3.5 | 2.8 |
| 22 – 30 | 8 × 7 | 4 | 3.3 |
| 30 – 38 | 10 × 8 | 5 | 3.3 |
| 38 – 44 | 12 × 8 | 5 | 3.3 |
| 44 – 50 | 14 × 9 | 5.5 | 3.8 |
| 50 – 58 | 16 × 10 | 6 | 4.3 |
| 58 – 65 | 18 × 11 | 7 | 4.4 |
| 65 – 75 | 20 × 12 | 7.5 | 4.9 |
| 75 – 85 | 22 × 14 | 9 | 5.4 |
| 85 – 95 | 25 × 14 | 9 | 5.4 |
| 95 – 110 | 28 × 16 | 10 | 6.4 |
| 110 – 130 | 32 × 18 | 11 | 7.4 |
| 130 – 150 | 36 × 20 | 12 | 8.4 |
| 150 – 170 | 40 × 22 | 13 | 9.4 |
| 170 – 200 | 45 × 25 | 15 | 10.4 |
| 200 – 230 | 50 × 28 | 17 | 11.4 |
| 230 – 260 | 56 × 32 | 20 | 12.4 |
| 260 – 290 | 63 × 32 | 20 | 12.4 |
| 290 – 330 | 70 × 36 | 22 | 14.4 |
| 330 – 380 | 80 × 40 | 25 | 15.4 |
| 380 – 440 | 90 × 45 | 28 | 17.4 |
| 440 – 500 | 100 × 50 | 31 | 19.5 |
It depends on the fit. Normal: shaft N9 and hub JS9 (general use). Tight: P9 in both (reversing loads or shock). Sliding: shaft H9 and hub D10, when the hub has to move along the shaft. The calculator gives the deviations in mm.
From the opposite side, not from the keyway edge: check d − t1 on the shaft and d + t2 in the bore with a caliper or micrometer. Example: a 1 1/4 in shaft with a 1/4 in key gives 1.125 in on the shaft and 1.375 in in the hub.
As a rule of thumb, 1 to 1.5 times the shaft diameter, never longer than the hub. If the torque capacity is not enough, use a longer key or two keys at 180°.
The one for the shaft diameter. In the sprocket calculator, the drawing generator adds the DIN 6885 keyway automatically from the bore.